ADA Depot - A Forum To Support Users of ADA Amplification Gear

Please login or register.

Login with username, password and session length
Advanced search  

News:

Need a Schematic? Check the Vault *MP-1 Classic Schematics Just Added!!

Pages: [1]   Go Down

Author Topic: Broken MC-1 - Where to send for Repair?  (Read 8802 times)

0 Members and 1 Guest are viewing this topic.

aoresteen

  • Newbie
  • *
  • Offline Offline
  • Posts: 2

I have two ADA MC-1 foot controllers.  One is dead, it does not power up.  The other one works perfectly.

Where should I send the broken MC-1 to for repair?

Thanks!
Logged

rnolan

  • Administrator
  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 5995
Re: Broken MC-1 - Where to send for Repair?
« Reply #1 on: Time Format »

You may be able to fix it yourself. How are you with electronics ? I don't think the MC-1 is particularly complicated and MJMP or others may be able to step you through the fix. It's certainly worth opening it up and check for anything obvious.
So your in Newnan GA USA, not sure where that is or who's the closest decent tech. Others here should have some recommendations.

@ MJMP, do you have a schematic for the MC1 ?
Logged
Studio Rig: Stuff; Live Rig: More Stuff; Guitars: A few

MarshallJMP

  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 4702
    • marshalljmpmodshop.net
Re: Broken MC-1 - Where to send for Repair?
« Reply #2 on: Time Format »

Nope no schematics for the MC-1.

The MC-1 isn't that easy to fix,you need a scoope or a logic probe to check it out.You can try to measure the 5V and after that it's ll digital.
Logged

rnolan

  • Administrator
  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 5995
Re: Broken MC-1 - Where to send for Repair?
« Reply #3 on: Time Format »

IIRC It's based on a Zialog Z80 CPU. We had to write a Z80 emulation program in Pascal when I was at uni, interesting assignment.
Logged
Studio Rig: Stuff; Live Rig: More Stuff; Guitars: A few

aoresteen

  • Newbie
  • *
  • Offline Offline
  • Posts: 2
Re: Broken MC-1 - Where to send for Repair?
« Reply #4 on: Time Format »

Thanks all!

I'm ok with electronics.  Issue is my bench is not set up.  I do have a scope & probes.  I'll look at the 9v/5v power feed and see if that brings it back to life.

I was hopping that there is someone out there that knows the MC-1 and can fix it faster than I can.
Logged

MarshallJMP

  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 4702
    • marshalljmpmodshop.net
Re: Broken MC-1 - Where to send for Repair?
« Reply #5 on: Time Format »

Well i could fix it for you but then you'll have to ship it to belgium.Since you have the equipment that would be a bit stupid.Let's try to fix trough this topic or email.So first check the 5V,starting from the dc adaptor input trough a diode (1N400x),then a cap into a 7805 regulator.If you have 5V at the output of the 7805 then the next thing to check is if you have a clock signal on pin 6 of the Z80 µcontroller.I need to check it out but i think it works on 2MHz.I have the pcb of MC-1 here and it seems it has a 4MHz crystal (buffered by a 74HC04 (hex inverter) pin 1 and 2) going to pin 3 of a 74LS74 (D flip flop),there it will be devided by 2 so you will have 2MHz on pin 5 of the 74LS74 then it goes to pin 3 of the 74HC04 and pin  4  goes to pin 6 of the Z80.Also make sure sure pin 26 (reset) is high (5V).
I hope this makes sence,if not let me know.BTW the 74hc04 is on the right side of the crystal,the LS74 on the left side.
« Last Edit: Time Format by MarshallJMP »
Logged

Dante

  • Administrator
  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 2123
  • Nothing more uncommon than common sense
    • The Best Cover Band In Sacramento
Re: Broken MC-1 - Where to send for Repair?
« Reply #6 on: Time Format »

MJMP to the rescue!!! (again)

rnolan

  • Administrator
  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 5995
Re: Broken MC-1 - Where to send for Repair?
« Reply #7 on: Time Format »

MJMP to the rescue!!! (again)
+1  :thumb-up: :bow:
Logged
Studio Rig: Stuff; Live Rig: More Stuff; Guitars: A few

MarshallJMP

  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 4702
    • marshalljmpmodshop.net
Re: Broken MC-1 - Where to send for Repair?
« Reply #8 on: Time Format »

 ::)
Logged

chrismilne

  • Newbie
  • *
  • Offline Offline
  • Posts: 2
Re: Broken MC-1 - Where to send for Repair?
« Reply #9 on: Time Format »

Did you have any luck?  I just tried to fire mine up after many, many years and no power...
Logged

MarshallJMP

  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 4702
    • marshalljmpmodshop.net
Re: Broken MC-1 - Where to send for Repair?
« Reply #10 on: Time Format »

Maybe a stupid question, but are you sure you're using a adaptor with the correct polarity?
Logged

chrismilne

  • Newbie
  • *
  • Offline Offline
  • Posts: 2
Re: Broken MC-1 - Where to send for Repair?
« Reply #11 on: Time Format »

Yeah, i still have the original ADA adapter.  Though i guess it could be bad...
Logged

MarshallJMP

  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 4702
    • marshalljmpmodshop.net
Re: Broken MC-1 - Where to send for Repair?
« Reply #12 on: Time Format »

Well that's easy checked with a multimeter.
Logged
Pages: [1]   Go Up