ADA Depot - A Forum To Support Users of ADA Amplification Gear

Please login or register.

Login with username, password and session length
Advanced search  

News:

Please note "Depot New Registrations Temporarily Suspended" Please see discussions for how to register.

Pages: [1]   Go Down

Author Topic: Marshall Cabs  (Read 7987 times)

0 Members and 1 Guest are viewing this topic.

Mxzx

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 63
Marshall Cabs
« on: Time Format »

I just got a B200s off of Ebay, and was wondering if I can run two 16 ohm 4x12's through it?  I don't have the manual for it, but seller says it can do 100w into 8 ohms, or 135w at 4 ohms?  I do have a JCM-900 that has the stereo switching in the back that I think brings each pair of speakers to 8 ohms, so I can always to do a single cab.

Thanks
Logged

rnolan

  • Administrator
  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 5997
Re: Marshall Cabs
« Reply #1 on: Time Format »

The B200s does about 124w rms into 4 ohms and probably about 80w rms into 8 ohms.  You'll do damage if you use a 16 ohm load.  It will pair well with the JCM-900 in stereo with each pair 8 ohms.  You can re wire the 16 ohm cabs to be 4 ohms or run both in parallel off one side of the B200 (ie 16 + 16 in parallel = 8).  4 x 16 ohm cabs are typically wired with each pair in parallel and then the series between the 2 pairs = 16 ohm box (or each pair in series and parallel between the pairs).  If you change the wiring to be all parallel  16 + 16 + 16 +16 = 4 ohm.
Logged
Studio Rig: Stuff; Live Rig: More Stuff; Guitars: A few

Mxzx

  • Jr. Member
  • **
  • Offline Offline
  • Posts: 63
Re: Marshall Cabs
« Reply #2 on: Time Format »

Cool, thanks for the info.

I think I'll just run it into one -900 cab in stereo.

Logged

rnolan

  • Administrator
  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 5997
Re: Marshall Cabs
« Reply #3 on: Time Format »

Sounds good  :thumb-up:
Logged
Studio Rig: Stuff; Live Rig: More Stuff; Guitars: A few

MarshallJMP

  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 4702
    • marshalljmpmodshop.net
Re: Marshall Cabs
« Reply #4 on: Time Format »

You can use 2 16 ohm cabs if you want,won't harm a thing,just the power will be lower.Around 50-60W /side.

JCM900 cabs have either mono 16 or 4 ohms input or  2 x 8 ohms stereo.Are both cabs JCM900 models?
« Last Edit: Time Format by MarshallJMP »
Logged

rnolan

  • Administrator
  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 5997
Re: Marshall Cabs
« Reply #5 on: Time Format »

Hey MJMP, that's good to know, I didn't think the B200 would be happy with a 16 ohm load, how would it react to 2 ohm load ?
Logged
Studio Rig: Stuff; Live Rig: More Stuff; Guitars: A few

MarshallJMP

  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 4702
    • marshalljmpmodshop.net
Re: Marshall Cabs
« Reply #6 on: Time Format »

2 ohm will be too low,it won't like that.
Logged

Dante

  • Administrator
  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 2123
  • Nothing more uncommon than common sense
    • The Best Cover Band In Sacramento
Re: Marshall Cabs
« Reply #7 on: Time Format »

This analogy works for me when it comes to amps into speaker cabs:

Ohms are like water in a hose. If you have a garden hose, you can plug it into a garden hose or a fire hose (something larger). You can NOT plug the garden hose into a drinking straw (something smaller). So, if we use the same logic here: If you have an amp that pushes 8 ohms, you can plug it into a cab that will handle 8 ohms (or 16 ohms = something larger).

It will not be good to plug your 8 ohm amp into a 2 ohm cab (which would be like the firehose into the drinking straw = something smaller).

Hopefully, that helps more than it hurts
Pages: [1]   Go Up