• Welcome to ADA Depot - A Forum To Support Users of ADA Amplification Gear.
 

MB-1 Restoration Parts List Needed....

Started by BoWeevil, May 09, 2014, 11:51:13 AM

Previous topic - Next topic

BoWeevil

Hello All!
I am a former MB-1 user and have just reacquired an MB-1 off of Reverb.
I'm looking to give this baby a complete overhaul, with the plan of keeping it as my FINAL preamp.
With that being said, I'm looking for a list of or a link to a supplier for all the best Mods and replacement parts I would need to get this pre in top operational condition.
I've seen the recommendations out there for the JJ/ECC83 tubes, as well as the MDRT.
Besides those, what else should I be looking at replacing?
Battery? Caps? Resistors? etc.....
Thanks, and looking forward to any and all replies,

BoWeevil
BoWeevil
boweevil@whoisbo.com

Peter H. Boer

Well hello BoWeevel,

I saw somebody mention that the old Depot was still somewhere on the net in the archives of something.
If somebody can point me to that I can see if I can find my old thread of the modifications done to my 2 MB-1s :thumb-up:

Welcome to your last preamp  O0
Nothing beats MB-1s and MP-1s with MDRTs

http://www.thegrannyattic.com
http://www.Illumion.net
http://www.sote.nl

MarshallJMP

You can also do the noise mod for the MB-1.

rnolan

Hey BoWeevel,
Quote from: Peter H. Boer on May 10, 2014, 04:22:04 AM
Welcome to your last preamp  O0
:thumb-up:
I've used MP1 now MP2 for over 25 years now and they are still (after all these years) IMHO the best preamps ever.  The thought of not having my MP2 cooking is not one I want to contemplate...  They are getting older though and there are some options to give them a grease, oil and bearing change, particularly to use better more modern components and replace the bits and bobs that die over time (seems to be caps mostly ??).
Peter is the guru on MB1s, so I hope you/he can dig up his posts.  MJMP is the mod master  :bow: and is sure to help...
Change tubes (always a good idea depending how old they are).  I'll mostly defer to Peter here as I don't have a MB1 but JJs are usually good (lots of fully tested re-badged JJ options, Boogie STRs, Rubys, Grove Tube etc), personally I'd give the new sensor Mullard short plates a go, they are IMHO better on guitar than JJs and should have the feq response for bass, and they are sooo 3D mmmm. Then, tubes are very subjective.
To my mind, the MDRT is a no brain-er, if you can afford it, put it in (http://www.marshalljmpmodshop.net/miscellaneous_parts_and_replacement_tubes.htm), I wish there were one for my MP2.
Battery, IIRC there is a mod for that (probably similar to the MP1 battery mod), good idea (considering how old the units are)
Caps, for any that go off over time it will be worth replacing them with better (longer lasting) more modern caps
Resistors, again similar to caps, if there are better modern components ? MJMP will know..
Opp Amps, Soli (IIRC) replaced every opp amp he could in his MP1 with newer better specked (where he could) etc and said the improvement was amaizing, this is a big(ish) job though ?
Anyway, welcome to ADA heaven, cheers Richard
Studio Rig: Stuff; Live Rig: More Stuff; Guitars: A few

kawai2g4b

+1 on JJs.  Just had them installed in mine.
Pearce G2R with ADA TFX4 in loop.
ADA MB-1/B500B
And other non ADA stuff.

Kawai AQ-500 guitar, Korean Fender Lite Ash Strat, Electra X930 MPC modded, G&L L2K basses, Peavey T40, Fernandes basses.

BoWeevil

Thanks for the info!
As far as the MDRT goes, is there only one for the MB-1?
BoWeevil
boweevil@whoisbo.com

rnolan

I wish there were only 1 for the MP2, yes there is only 1 MDRT (for MP1/MB1), (Machinator Developed Replacement Transformer) go Machinator  :bow: I tried to get him interested in a MP2 version but he's way too busy...  Any one else interested in designing a new tranny for the MP2 ?
Studio Rig: Stuff; Live Rig: More Stuff; Guitars: A few