I used a Warmoth roasted Swamp Ash body with Maple neck. The installation was tricky - don't attempt this unless you have some luthier and woodworking skills!
I still have to work out the power source; my original plan to use the Fishman Fluence battery failed, so I need to add a battery box instead. Otherwise, it works fine; it's nice to have the two encoders on the guitar so I don't have to mess with fret control!
![](http://www.snapagogo.com/uploads/source/852017/1490623429_870256235_IMG_2054.jpg)
![](http://www.snapagogo.com/uploads/source/852017/1490623438_1066593893_IMG_2055.jpg)
A Warmoth Roasted Swamp Ash body. Tape marks for pick guard edge
![](http://www.snapagogo.com/uploads/source/852017/1490623231_1718443477_IMG_1996.jpg)
Cavity routed for ATG DSP board
![](http://www.snapagogo.com/uploads/source/852017/1490623239_873993301_IMG_2004.jpg)
It fits!
![](http://www.snapagogo.com/uploads/source/852017/1490623247_244607707_IMG_2005.jpg)
Application of conductive paint to all cavities
![](http://www.snapagogo.com/uploads/source/852017/1490623307_277892259_IMG_2021.jpg)
Ready for electronics
![](http://www.snapagogo.com/uploads/source/852017/1490623315_306803049_IMG_2022.jpg)
Marking and installing hex pickup
![](http://www.snapagogo.com/uploads/source/852017/1490623261_1724144414_IMG_2007.jpg)
Test fitting finished pick guard, Wilkinson tremolo, and output jack
![](http://www.snapagogo.com/uploads/source/852017/1490623270_496299346_IMG_2008.jpg)
Hole for 8-pin MIDI jack
![](http://www.snapagogo.com/uploads/source/852017/1490623277_1733923659_IMG_2009.jpg)
Test fitting MIDI jack
![](http://www.snapagogo.com/uploads/source/852017/1490623285_323267898_IMG_2010.jpg)
Test fitting Fishman Fluence battery pack (this is before I concluded that it could not supply enough current for the ATG)
![](http://www.snapagogo.com/uploads/source/852017/1490623297_1722026508_IMG_2012.jpg)
After True-Oil finish. MIDI wiring and batter cable are installed
![](http://www.snapagogo.com/uploads/source/852017/1490623345_236543565_IMG_2044.jpg)
Output and 8-pin MIDI jacks installed
![](http://www.snapagogo.com/uploads/source/852017/1490623361_1391260781_IMG_2046.jpg)
Pick guard and DSP board wired up and ready! Note the single wire connectors
![](http://www.snapagogo.com/uploads/source/852017/1490623369_843380189_IMG_2047.jpg)
The big moment - will it all fit right?
![](http://www.snapagogo.com/uploads/source/852017/1490623377_591902548_IMG_2048.jpg)
It was tight, but everything fit
![](http://www.snapagogo.com/uploads/source/852017/1490623384_404820777_IMG_2050.jpg)
Battery connection and ground in the tremolo cavity
![](http://www.snapagogo.com/uploads/source/852017/1490623396_1881644584_IMG_2051.jpg)
Warmoth Birdseye Maple neck attached. All hardware is black!
![](http://www.snapagogo.com/uploads/source/852017/1490623404_1134528239_IMG_2052.jpg)
Tuner double pin holes drilled using StewMac template tool
![](http://www.snapagogo.com/uploads/source/852017/1490623322_127168685_IMG_2040.jpg)
Schaller M6 locking tuners installed
![](http://www.snapagogo.com/uploads/source/852017/1490623329_345426845_IMG_2041.jpg)
Love these tuners!
![](http://www.snapagogo.com/uploads/source/852017/1490623336_843418379_IMG_2042.jpg)
Top of the neck showing Birdseye Maple fingerboard
![](http://www.snapagogo.com/uploads/source/852017/1490623417_12121327_IMG_2053.jpg)
Close-up of controls. Note the two encoders between volume (top) and tone (bottom). I designed custom dials for each encoder
![](http://www.snapagogo.com/uploads/source/852017/1490623445_643066430_IMG_2083.jpg)
Sounds great! The two encoders greatly improve on the AT-200.