ADA Depot - A Forum To Support Users of ADA Amplification Gear

Please login or register.

Login with username, password and session length
Advanced search  

News:

Need a Schematic? Check the Vault *MP-1 Classic Schematics Just Added!!

Pages: 1 [2] 3 4   Go Down

Author Topic: ADA Microtube 200 Help Needed  (Read 28346 times)

0 Members and 1 Guest are viewing this topic.

davec69

  • Newbie
  • *
  • Offline Offline
  • Posts: 32
Re: ADA Microtube 200 Help Needed
« Reply #15 on: Time Format »

Any ideas on how i should proceed, what I should check or replace?
Logged

davec69

  • Newbie
  • *
  • Offline Offline
  • Posts: 32
Re: ADA Microtube 200 Help Needed
« Reply #16 on: Time Format »

Well, I think I've found the source of the problem.  I pullout the pcb (this time, all the way), so I could replace the neon, and was greeted with a mess on the back of the pcb.  Looks like there was a rubber foot on the back, which was placed right under the C37,D25,D26,R42, which melted/disinigrated, and created a mess.  (See pics)

I used some goof off to clean off all the black goo, then sprayed some Deoxit to remove the corrosion.  The PCB is now clean again.  I also cut out a new card to shield the PCB from the metal enclosure.

I also since I had the pcb out, I replaced R42 (200ohm/.5w).

Same symptoms still persist.  Unit powers on, protect light off, no sound when taken off standby.










« Last Edit: Time Format by davec69 »
Logged

MarshallJMP

  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 4702
    • marshalljmpmodshop.net
Re: ADA Microtube 200 Help Needed
« Reply #17 on: Time Format »

What happends with the voltages if you disconnect 1 or 2 of those big connectors carrying the voltages, do they stay the same?
Logged

Sparker

  • Full Member
  • ***
  • Offline Offline
  • Posts: 103
Re: ADA Microtube 200 Help Needed
« Reply #18 on: Time Format »

Ok.  Here's the measurements from the other connector on the preamp boards.  There are four wires.  Red, Green, Black, White.  I used the black wire as the ground.

Red / Black = 3.736v
Green / Black = 11.89
White / Black = 092.2v

The measurements for both channels were pretty much the same.


Can you measure the PSU voltages again, using the Green wire as the 0V/Ground ref as follows -

1 = White = +75V
2 = Black = -12V
3 = Green = 0V
4 = Red = +170V

Let us know
Logged
ADA Gear: MP-1 Tube Board

davec69

  • Newbie
  • *
  • Offline Offline
  • Posts: 32
Re: ADA Microtube 200 Help Needed
« Reply #19 on: Time Format »

New measurements below. 

I also tried it with one of the connectors, disconnected, and the reading was the same on the other channel. 
FYI.  I did notice on the front panel, that all the leds for one side were lit, while the connector was disconnected.

1 = White = +75V (80.5v)
2 = Black = -12V (11.88v)
3 = Green = 0V
4 = Red = +170V (08.10v)

Let us know
Logged

Sparker

  • Full Member
  • ***
  • Offline Offline
  • Posts: 103
Re: ADA Microtube 200 Help Needed
« Reply #20 on: Time Format »

Looks like there could be a problem around Q9 (TIP48) in the PSU - this is part of the HV regulator (buy a couple). This might not be the only fault though, but I would start with trying to get that +170V rail back up first. Would also be a good idea to get a couple of the Q10 as well - MPSA42.
« Last Edit: Time Format by Sparker »
Logged
ADA Gear: MP-1 Tube Board

MarshallJMP

  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 4702
    • marshalljmpmodshop.net
Re: ADA Microtube 200 Help Needed
« Reply #21 on: Time Format »

Also check R34 should be 220k, sometimes these go up in value.
Logged

davec69

  • Newbie
  • *
  • Offline Offline
  • Posts: 32
Re: ADA Microtube 200 Help Needed
« Reply #22 on: Time Format »

So, I swapped out the TIP48 last night, and noticed that one of the legs was broken on theold part.  After the swap, I still get the same voltages on the 4 pin connector.

Tonight, I will replace R34, and the MPSA42, and report back.
Logged

davec69

  • Newbie
  • *
  • Offline Offline
  • Posts: 32
Re: ADA Microtube 200 Help Needed
« Reply #23 on: Time Format »

Tonight I swapped out the 220K R34 resistor, and Q10 (MPSA42).  No change.  I'm still getting -8v between the Green and Red connector.
Logged

Sparker

  • Full Member
  • ***
  • Offline Offline
  • Posts: 103
Re: ADA Microtube 200 Help Needed
« Reply #24 on: Time Format »

Just to make sure, this is with both PSU connectors pulled from the power amp boards and not in standby?
Logged
ADA Gear: MP-1 Tube Board

MarshallJMP

  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 4702
    • marshalljmpmodshop.net
Re: ADA Microtube 200 Help Needed
« Reply #25 on: Time Format »

Can you measure the voltage on the standby switch, one side to ground (green), when the standby is off both sides should have around 220V
Logged

davec69

  • Newbie
  • *
  • Offline Offline
  • Posts: 32
Re: ADA Microtube 200 Help Needed
« Reply #26 on: Time Format »

I checked the voltage to the two connectors on the standby switch, to the green ground on the 4 pin connector. 

First connector on standby switch to ground = 6.9v
Second connector on the standby switch to ground = 50v

When I flipped the standby switch on, I measured 6.9v on both connectors.

Also, I am now hearing a crackling sound from something.  Very faint, and sporadic crackling.  I couldn't track it down.
Logged

rnolan

  • Administrator
  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 5998
Re: ADA Microtube 200 Help Needed
« Reply #27 on: Time Format »

Hmm crackling often = bad solder joins, a good thing to do (regardless) is re-flow (remelt) all the solder joins particularly around the power supply (was suggested by MJMP and fixed my (crackling) B200s :thumb-up: ).
Logged
Studio Rig: Stuff; Live Rig: More Stuff; Guitars: A few

MarshallJMP

  • Superhero Member
  • ******
  • Offline Offline
  • Posts: 4702
    • marshalljmpmodshop.net
Re: ADA Microtube 200 Help Needed
« Reply #28 on: Time Format »

Can you measure the voltage over R30 and R40?
Logged

davec69

  • Newbie
  • *
  • Offline Offline
  • Posts: 32
Re: ADA Microtube 200 Help Needed
« Reply #29 on: Time Format »

Measurements from R30 & R40 were a little weird.

Amp powered on in standby, and I got:

R30 = 182v (1st measurement) then I checked again and got 19v.
R40 = -7.92v

Measurement when not in standby

R30 = 7v
R40 = 7.92v

Not sure if it matters, but the led in the power switch also flickers on and off on occassion.

Logged
Pages: 1 [2] 3 4   Go Up